Your watercooling and modding distributor Your watercooling and modding distributor

flow meter GMR Transparent incl. electronics G1/2' outer thread - Highflow - Electronic incl.

  • 71043
  • AFS1-T1/2
  • 4049469030100
  • 0,051 kg

> 25 gata de livrare, timp de livrare 1-3 zile

49,99 € *

Preturi incl. VAT plus shipping costs

Accesorii recomandate
Plata extra
Phobya Thread sealing tape 12mmx10m
1x
Phobya Thread sealing tape 12mmx10m
2,09 €*
O-Ring 19 x 12 x 8 mm flat seal NBR50 (Adapter G1/2 and GMR)
1x
O-Ring 19 x 12 x 8 mm flat seal NBR50 (Adapter G1/2 and GMR)
1,69 €*
Finally we can offer flow sensors for Highflow systems. What sets this sensor apart from the...more
Product Information

Finally we can offer flow sensors for Highflow systems. What sets this sensor apart from the other products on the market is the fact that the flow is barely obstructed. The sensor is equipped with a 1/2" outer thread, therefore an adaptor piece (Art.No. 64002 and 95015) or special fittings are required.

This version is additionally equipped with monitoring electronics which can be connected to common monitoring devices such as the Aquaero or the T-Balancer etc. via a 3-Pin cable. A special nozzle for systems with lower flow rates included.

Technical data:
Without nozzle: Measurement possible from 60l/h with 492 pulses per liter
With nozzle: Measurement possible from 30l/h with 1200 pulses per liter (The nozzle may result in some problems with some monitoring devices with flow rates in excess of 100l/h)

To conclude: This flow rate sensor is perfect for anyone who wants minimum flow resistance. Even users with less powerful pumps and flow-oriented cooling loops can use this sensor as measurement is possible from 30l/h up.

Summary:
+ Very low flow resistance
+Almost inaudible at common flow rates
+ Noise emission only with high flow rates, and even then very quiet operation

Inlet is the side with the smaller diameter, Outlet the side with the larger inner diameter.

Flow sensor round-up

Please note: When professionally installed the GMR seals tightly with the seal. Otherwise please use additional Phobya Thread sealing (Art.No.: 32002).

Note:
Using reducer couplers must be used a little thread sealing tape so that it seals to 100%!

Note on sensor compatibility:
Flow rate sensors are only suited to be connected to a compatible monitoring device and CAN NOT be directly connected to e.g. the fan connector on a Mainboard, as the sensors do not output the required pulse rate as a fan does. The only way of realizing such an arrangement is the Pulsmatik (Art.No.: 71000) which can be looped in between sensor and Mainboard. For the pure cost factor we do not recommend this solution but rather the purchase and connection of a compatible fan monitor and controller.

Note regarding power supply:
Should the values from the flow sensor vray greatly, the input voltage is too low. To solve this problem it suffices to connect the +5V lead not to the +5V output of the controller but to the +12V supply from the PSU. As the sensor requires a voltage of 5-24V and some controllers only supply 4.9V these deviation may be caused.

Videos
Technical details and videos ... moor
Technical details
Questions & Answers more
Questions & Answers
2 Întrebări în alte limbi.
Faceți clic aici pentru a afișa această întrebare.
Question from SebO from 08. August 2018
Hier in der Beschreibung wird 1200 Pulsen pro Liter mit Düse angegeben. Auf der Homepage des Herstellers GMR aber 828 Pulsen pro Liter (mit Düse). Was ist nun korrekt? Die Angaben ohne Düse stimmen überein.
Antwort von Aquatuning GmbH vom 08. August 2018
Es müssten 828 Pulse pro Liter sein.
Question from Guest #363831 from 04. April 2019
Wenn die Lüfteranschlüsse meines Mainboards 200rpm und weniger anzeigen können, kann ich den Sensor dann auch direkt ans Mainboard anschliessen? Hier steht ja was von 492 Pulsen/Liter und ich gehe davon aus, dass mein Kreislauf mind 1L/min schafft. Mir ist klar, dass ich möglicherweise das Anschlußkabel anpassen muss indem ich ein passendes 3-Pin-Kabel anlöte.
Antwort von Aquatuning GmbH vom 05. May 2019
Ja das können Sie so machen. Wenn Sie das Tachosignal erhalten müssen Sie es aber irgendwie auch wieder umrechnen um einen sinnvollen Wert zu erhalten.
Read, write and discuss reviews...more
Reviews
5 stele:
(0)
4 stele:
(0)
3 stele:
(0)
2 stele:
(0)
1 stele:
(0)
Alphacool tubing AlphaTube HF 13/10 (3/8"ID) - clear 3m (9,8ft) Retailbox Alphacool tubing AlphaTube HF 13/10 (3/8"ID) -...
Continut 300 cm (3,67 € * / 100 cm)
11,00 € *
Aquacomputer Double Protect Ultra 1000ml Aquacomputer Double Protect Ultra 1000ml
Continut 1000 ml
10,16 € *
-20%
GELID Solutions GC Extreme Thermal Compound GELID Solutions GC Extreme Thermal Compound
Continut 3.5 g (2.084,29 € * / 1000 g)
7,30 € *
-68%
Alphacool Laing DDC-SilentBox Alphacool Laing DDC-SilentBox
6,49 € * 19,99 € *
Phobya Y-Cable 3Pin Molex to 4x 3Pin Molex 60cm -  black Phobya Y-Cable 3Pin Molex to 4x 3Pin Molex 60cm...
Continut 60 cm (9,14 € * / 100 cm)
5,49 € *
-3%
LEDready 5mm ultra-bright green LEDready 5mm ultra-bright green
2,12 € * 2,19 € *
Phobya 4Pin Molex power extension 60cm - black Phobya 4Pin Molex power extension 60cm - black
Continut 60 cm (9,14 € * / 100 cm)
5,49 € *